REMI Fiber Transmission Rack
Ithaca College Television’s Bombers Live basketball coverage operates as a REMI-style production between Hill Center and the Roy H. Park School of Communications studios. Rather than deploying a full truck, we rely on fiber infrastructure to transport video, audio, intercom, IFB, and network connectivity between venues.
To support this workflow, I built a compact remote transmission rack designed for maximum flexibility and modularity.
System Capabilities
The rack supports:
Up to 8 SDI transmit paths
4 SDI receive paths
4 XLR Dante inputs
4 XLR Dante outputs
Full network connectivity over fiber
The goal was simple: create a system that could adapt to changing production needs without rewiring the entire show every game.
Remote Rack Playbook
Bombers Live - Spring 2026
Last Modified: 1/25/2026
Overview


IP Addresses
Model | Device Name | Management IP | Dante IP |
AEQ Olympia 3 | OLYMPIA3-103585 | redacted | redacted |
PTZOptics Move 4K | PTZOptics 2 | redacted | -- |
PTZOptics Move 4K | PTZOptics 3 | redacted | -- |
PTZOptics Move 4K | PTZOptics 1 | redacted | -- |
Blackmagic Videohub 12 x 12 | Remote Rack Videohub 12 x 12 | redacted | -- |
NA2-IO-DPRO | Neutrik1-Hoops | redacted | redacted |
NA2-IO-DPRO | Neutrik2 | redacted | redacted |
Blackmagic Videohub Router 12x12
Inputs 1-8 are the SDI connections on the rear of the rack
Inputs RED 1-4 are received (RX) through the Barnfind
Outputs RED 1-4 are transmitted (TX) to the RED Barnfind
Outputs BLUE 1-4 are transmitted (TX) to the BLUE Barnfind
QC 1 is the left monitor and QC 2 is the right monitor on the front of the rack
Outputs 11 and 12 are SDI connections at the rear of the rack utilized for any purpose
Routing can be configured via the button menu on the front of the unit or the Blackmagic Videohub Control Software
Input | Output |
Input 1 | RED 1 |
Input 2 | RED 2 |
Input 3 | RED 3 |
Input 4 | RED 4 |
Input 5 | BLUE 1 |
Input 6 | BLUE 2 |
Input 7 | BLUE 3 |
Input 8 | BLUE 4 |
RED 1 | QC 1 |
RED 2 | QC 2 |
RED 3 | Output 11 |
RED 4 | Output 12 |

Olympia 3 - Commentator Box
Power via the PoE port on the rear of the commentator box connected to the labeled commentator RJ45
‘On’ button turns on mic and illuminates red lights, what goes to program is controlled in the studio
‘Coord’ allows for talkback on Hollyland channel B and mutes their mic off production
Director’s track on the SSL has a routed output to Olympia Receive Ch 5 Coord
In the CU Control software you can send tone instead of turning on a mic to test, set compressor limits, and adjust gain
Feedback - when the display shows a solid speaker icon , the source is routed to the headphones. When the speaker symbol is displayed empty , the audio from that source is not activated on the headphones. Utilize the button to the right adjust

Transmit | Dante Channel | Receive |
ANC1 | 1 | FB-Prog1 |
ANC2 | 2 | FB-Prog1 |
ANC3 | 3 | |
Truck IFB | 4 | |
Coord | 5 | FB-Coord |
6 | ||
XLR In L | 7 | XLR Out L |
XLR In R | 8 | XLR Out R |

Neutrik AVIO - XLR Interface
Each unit has two inputs and two outputs
Inputs are configured as LINE sources currently; it can be changed in the software by changing the input to MIC, and phantom power (+48v) becomes available
XLR must be connected to input or output 1, before an xlr connect to input or output 2 as it sends an AES digital audio signal instead of analog. The LED lights in the top right corner indicate if it's an analog signal with a blue light or red for AES

Dante Overview
Dante Controller allows you to manage the audio routes via transmitters and receivers, opening up the layers with (+). You can see which devices have a connection status indicated by a green check mark. To make a new connection, open up the view for your transmitter and receiver, and make a check mark to make a connection
To view if something is receiving a signal with audio, open up device view, select your device from the drop-down, and go to the transmit tab
Barnfind, Fiber, and Network
Barnfind operates in multiplexing, in which we have several signals combined over a single fiber and split back out on the other end
The Barnfinds must be connected in the same order on both sides: red, green, blue RGB. Both ends Park and Hill are connected Peer to Peer and then Cascade to Peer followed by the other Barnfinds. You will see a green status LED light when connected
Red and Blue Barnfind each have 4 SDI inputs and 4 SDI outputs, so we have 8 inputs transmitted (TX) to Park and 4 inputs received (RX) from Park
The Green Barnfind operates with an SFP port allowing either an SFP module to an SDI in and out or an SFP module to ethernet RJ45 connection. The rack receives network connectivity over this RJ45 connection.
If you are not receiving green status lights on the Barnfind, try swapping the fiber pairs
If you are not receiving network connectivity, double-check that the ethernet cable is secure to the SFP module, as the connection is loose
The left 3 network ports on the rear of the rack have their own separate PoE injectors
At Hill Center, the media service panel is located outside of the gym by the two maintenance parking spots. Connect the fiber to port 1. There is a PVC passthrough around the corner by the doors to feed the cable through. You will need a screwdriver and a wrench to open
Sideline IFB
A Lectrosonics IFB transmitter receives an XLR line connection from the Neutrik1-Hoops XLR output 1. In Studio B on the SSL there is a mix minus routed to the Neutrik with program and Hollyland channel B minus sideline mic
On the rear of the rack, there is a BNC connection for the IFB antenna





